DIY Ceiling Light Fixture Made With Branched Out Socket Splitters

Whereas electrical tasks might sound intimidating to the start DIYer, this ceiling mild fixture venture is one which, actually, anybody can do. Should you can screw in a lightbulb and wield a can of spray paint, you’re greater than certified to deal with this stylish little lighting quantity.

Supplies Wanted:

  • 1 porcelain cover
  • thirteen “Y” socket adapters/splitters*
  • 14 clear globe lightbulbs (25 watt, or 2 watt globe LEDs)*
  • 1 ceiling medallion (non-compulsory, however really helpful. Instance exhibits a ten” plastic medallion, spray painted white earlier than beginning)
  • Gold/metallic spray paint
  • Painters’ tape (just a bit)

*Tip: The variety of socket splitters you’ll use is strictly one fewer than the variety of globe lightbulbs you’ll want. For instance, if you need a smaller department mild with solely 10 socket splitters, you’ll want eleven lightbulbs.

Step 1: Assemble socket splitters.

This can be a therapeutic and enjoyable course of, however you’ll need to begin with one socket splitter and department off from there. Be loosely artistic on this course of. (Photograph exhibits simply 12 splitters; I forgot one right here however added it later.)

Whenever you’re assembling the splitters, be sure you screw them collectively firmly however don’t overtighten. Additionally, examine to be sure that there’s enough area for every lightbulb; that’s, don’t have two sockets aimed on the similar area, since you gained’t be capable of match two lightbulbs there.

Step 2: Tape off electrical.

If you’re proud of the configuration, tape off all electrical elements. This consists of inside every uncovered socket in addition to the very prime (or base, relying on how you consider it) splitter attachment. Additionally tape off electrical element inside your porcelain cover.

Your accomplished, taped off department mild configuration may look one thing like this once you’re completed.

Step three: Paint cover and branches.

Together with your electrical elements protected behind painters’ tape, you’re able to spray paint your fixture. Spray a number of very mild coats of the colour of your selection, and be sure to change the angle of your spraying (transfer across the configuration) and the sunshine fixture itself. There are tons of nooks and crannies which are straightforward to overlook in the event you’re not cautious. I did about eight coats in complete, rotating the whole lot every time.

Step four: Take away all tape.

This one’s fairly self-explanatory. Watch out to not twist your socket splitters (and probably crack the paint) as you take away the painters’ tape. Double verify to ensure all electrical elements are away from paint.

Step 5: Put together to mount the department mild: Take away present mild fixture.

Assuming you’re constructing this DIY department mild as a alternative for an present fixture, merely flip the breaker to the prevailing mild fixture (so there’s zero electrical energy operating to the wires), then un-wire and take the prevailing fixture down. You ought to be left with a floor (uncovered) wire, two electrical wires, and two screws protruding from the electrical field.

Step 6: Loosely place medallion in place. (elective)

In case you’re utilizing a ceiling medallion (I used a ten” plastic one, spray painted matte white), set it towards the ceiling earlier than you wire your cover.

Step 7: Wire the cover.

Connect every electrical wire to the cover, as proven. All the time watch out when working with wiring; ask for assist should you want it. (Word: I didn’t want the assistance, per se, however my father was visiting and wanted a undertaking, so he hung this mild for me. Hooray for fathers.)

Step eight: Mount porcelain cover.

When your wires are securely hooked up to the porcelain cover, it’s time to mount the cover. Keep in mind the 2 screws that have been poking out of the ceiling from eradicating our present mild fixture? Use these to mount the cover. Slide the screw heads via the bigger holes on the cover, then twist gently to align the screws with the smaller holes.

Tighten the screws securely. This will even maintain the medallion completely in place. Don’t overtighten!

Step 9: Connect department mild.

Rigorously screw within the base socket splitter of your department mild, taking care to keep away from cross-threading or overtightening.

Step 10: Set up bulbs and switch it on.

Screw in your 14 globe mild bulbs, flip the breaker to show the electrical again on, and switch in your mild. This image doesn’t do the gloriousness justice, however belief me. You’re going to be amazed at how brilliant and trendy and superior your department mild is.

Right here’s the department mild put in in a toddler’s room. It’s trendy and nicely-proportioned for such an area; the department mild would additionally look superior in an entryway, a house workplace, a bed room, or any room the place it gained’t be overwhelmed, actually.

Good luck in your DIY challenge in creating this department mild. I hope you’re keen on yours as a lot as I really like mine!

  • Facebook
  • Google Plus